John Deere 2653a Tripple Bladed Ride On Mower

John Deere 2653A Cylinder Tripple Blade ride on mower which is a great bit of kit which I have owned and used for several years. Diesel and hydrostatic. All wheel drive. Starts on the button and is super easy to use. Machine cuts but needs the blades re adjusting/checking/setting up to cut perfectly again. Leak of engine oil on cooler piping suspected to be fixed. Tyres also older. Front spirals removed as we found it easier to cut with these off. All these points taken into consideration with the on price. Would be a great machine for a local sports club etc. Super maneuverable. Full payment before machine is collected. Serious inquiries only. John Deere Info: Engine Specifications Make Yanmar 3TNE68A Engine Model Number 3008D002 Horsepower 13.4 kW (18.0 hp) Cylinders 3 Displacement 0.784 L (47.8 cu in.) Bore 68 mm (2.68 in.) Stroke 72 mm (2.83 in.) Valve Clearance 0.20 mm (0.008 in.) Lubrication Pressurized Oil Filter Full Flow Filter Air Cleaner 4 in. Radial seal, dual stage, restriction indicator Cooling Liquid Fuel SystemFuel Diesel Electrical SystemType 12 Volt ignition glow plug via rocker switch Battery Size 480 Cold Cranking Amps @ -18?C (0?F) Fluid CapacitiesFuel Tank 28.0 L (7.4 gal) Hydraulic Reservoir) 20.8 L (5.5 qt) Cooling system 4.0 L (4.2 qt) Engine Oil (with filter) 3.0L (3.1 qt) Wheel Motor and Reel DriveDrive Wheels Front, with standard third (rear) wheel drive Traction Drive Hydrostatic, 2-pedal Pump Gear Reel Control Valves Electro-hydraulic Filtration 10 microns 100 mesh strainer Cutting Unit Lift Hydraulic cylinder for front two units and hydraulic cylinder for center unit Travel SpeedsMowing 0-8.1 km/h (0 - 5 mph) Transport 0 - 12.8 km/h (0 - 8 mph) Reverse 0 - 8.1 km/h (0 - 5 mph) Cutting UnitsNumber 3 Size 66 cm or 76.2 cm or (26 in.) (30 in.) Backlapping Standard on machine, variable speed adjustment Clip frequency: 5 blade units 0.323/km/h (0.201/mph) Clip frequency: 8 blade units 0.203/km/h (0.126/mph) Reel Diameter 17.8 cm (7 in.) Bed Knife Adjustment 0.05 mm (0.002 in.) Number of Blades 5 or 8 Steering and BrakesBrake Type Dual 20.3 cm (8-inch) disk Steering Hydraulic Power DimensionsWheelbase 140 cm (55 in.) Tread Width 132 cm (52 in.) Mowing position width with 26-inch reels 183 cm (72 in.) Mowing position width with 30-inch reels 213 cm (84 in.) Turning radius uncut circle with 26-inch reels 50.8 cm (20 in.) Turning radius uncut circle with 30-inch reels 40.6 cm (16 in.) Weight (full fluids, no operator with cutting units) 789 kPa (1740 lb) TiresFront - 20x10-10 151.7 kPa (22 psi maximum) Rear - 20x10-8 82.7 kPa (12 psi maximum) Recommended LubricantsEngine Oil John Deere PLUS-50® Engine Coolant Ethylene Glycol Base Transmission Oil John Deere HY-GARD® Grease John Deere Special Purpose HD Water Resistant Grease John Deere Multipurpose HD Lithium Complex Grease John Deere Special Purpose HD Cornhead Grease John Deere Special Purpose Cotton Picker Spindle Grease (Specifications and design subject to change without notice.) Sound MeasurementAverage Sound Level2653A Greens Mower 88 LPA at 3400 r/min engine speed Sound pressure per 79/113/EEC. Sound power per four hemisphere method. Vibration MeasurementsHand/Arm Measured Per ISO 53492653A Greens Mower 1.5 m/s2 at 3400 r/min engine speed Whole BodyThe weig